% ---------------------------------------------------------------------
% PhotoMechanics 2015
% ---------------------------------------------------------------------
% May 27-29, 2015, Delft, The Netherlands
% ---------------------------------------------------------------------
\documentclass{Photomechanics2015}
% ---------------------------------------------------------------------
\title{Title in capital letters}
% ---------------------------------------------------------------------
\author{\underline{A. Firstauthor}, B. Secondauthor and C. Thirdauthor}
% ---------------------------------------------------------------------
\address{%
Department, University\\
Address, Country\\
email@address1, email@address2, email@address3\\
Please underline the name of the co-author who will present the paper at the conference\\
}
% ---------------------------------------------------------------------
\begin{document}
% ---------------------------------------------------------------------
\maketitle
% ---------------------------------------------------------------------

\begin{abstract}
This set of instructions follows the format required for the PhotoMechanics 2015 abstracts.
\end{abstract}

\section{Introduction}

The paper must be submitted in PDF format. Please follow the submission instructions on on the “Authors Center” Section of the PhotoMechanics 2015 web site (http://www.photomechanics2015.nl/content/authors) by November 26th 2014. 

\section{General requirements}

\subsection{Abstract Format}

This page is formatted in an {\bf A4 Standard size}. The recommendations for the margins are the following: left margin = 20 mm, right margin = 20 mm, top margin = 15 mm, and bottom margin = 15 mm.

\subsection{Abstract Length}

Abstracts including all figures and tables must not exceed 4 pages.

\section{Word processing}

\subsection{Font Type and Size}

All text must be {\bf 9 point Arial font}. The title, the authors and the addresses must be {\bf 10 point Arial font}.

\subsection{Language}

Papers must be written in English.

\subsection{Text Format}

All text should be {\bf single-spaced}. The text should be {\bf fully right and left justified}. Main Headings and Subheadings in this sample document are already formatted to provide the required spacing.

\medskip 

\noindent Use {\bf two separation lines} with the following:\begin{itemize}
\item Immediately after Authors’ names and addresses
\end{itemize}

\noindent Use {\bf one separation line} with the following:
\begin{itemize}
\item Immediately after paper title
\item Immediately before and after equations
\item Immediately before and after Tables
\item Immediately before and after Figures
\item Between Paragraphs
\end{itemize}


\subsection{Equations}

Place equations and formulae centred in separate lines. Number Equations consecutively with the equation number placed flush to the right margin in parenthesis. Example of equation:
\begin{equation}
{\mathbf K}{\mathbf U} = {\mathbf F} 
\end{equation}

\section{Figures and Tables}

The number of tables and figures should be limited. Figures and Tables should be referred to in text as figures using Arabic numerals e.g. Fig. 1, Table 1 etc, in order of appearance. Captions should be bold and centred immediately below illustrations and tables. Example of caption:
\begin{figure}[htbp]
\begin{center}
\caption{Caption}
\label{default}
\end{center}
\end{figure}


\section{References}

References should be cited in the order in which they appear in the text and indicated with a number in square brackets in the text at the relevant point e.g. [1].

\medskip
\noindent The following are examples of style:


% ---------------------------------------------------------------------
\begin{thebibliography}{1}
% ---------------------------------------------------------------------
\bibitem{article}Dulieu-Barton, J.M. and Quinn, S. (1988) Thermoelastic stress analysis of oblique holes in flat plates. \emph{Int. J. of Mech. Sci.} 41, 557-546 
\bibitem{livre} Broberg, K.B. (1999) Cracks and Fracture. \emph{Cambridge University Press}, Cambridge
\bibitem{acte} Lesniak, J.R. and Boyce, B.R. (1994) A high speed differential thermography camera. \emph{Proc. SEM Spring Conf. on Exp. Mechanics}, Baltimore, 491-497


% ---------------------------------------------------------------------
\end{thebibliography}
% ---------------------------------------------------------------------

% ---------------------------------------------------------------------
\end{document}
% ---------------------------------------------------------------------

